Western Telematic PollCat III Betriebsanweisung Seite 14
- Seite / 147
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3.2. Connecting the Data Cables and Telephone Line
Prior to installing cables, you will need to select a method for access to PollCat III's Command
Mode, and decide where alarms and callbacks will be directed.
Command Mode Access: The Command Mode allows the user to manage PollCat III's various
features and poll data received from the PBX. There are three possible cable configurations:
·
Local Access: PollCat III is managed by a local PC connected by cable to the Computer
Port.
·
Remote Access: PollCat III is managed by a remote PC that communicates with the unit
via modem.
·
Both Local and Remote Access: PollCat III can be managed by a local PC, or by a
remote PC. Note that only one Access method can be used at a time.
Alarm Notification: When an alarm or callback is generated, PollCat III offers several
methods to notify the user. There are three possible cable configurations for alarm
notification:
·
Local Notification: Alarms are sent by cable to a local PC.
·
Remote Notification: Alarms are sent via modem to a remote PC or Pager.
·
Combination of Methods: Alarms are sent to a local PC, or a remote PC or pager. The
PollCat III cannot be configured to simultaneously provide both local, remote, and pager
alarm notification. Providing the proper cabling and hardware is present, Command ^B87
can be used to switch notification methods as needed.
The cable layout for your system will be determined by the access and notification methods
selected. Determine which method(s) will be used, refer to the diagram in Appendix B and
install data cables and telephone line as outlined in the following sections.
CAUTION: Prior to connecting data lines, make certain the cables are
compatible with PollCat III. Please refer to the interface pin-out information
in Appendix C.
3.2.1. PBX Inputs A and B
The PBX Inputs are used for connection to your PBX SMDR Ports. PollCat III includes two
PBX Inputs to allow the unit to receive call data from two separate PBX units. Make certain to
use data cables that are compatible with the PBX Input Port Interface, as described in
Appendix C.
3-4
PollCat III - Pollable Call Accounting Terminal, User's Guide Hardware Installation
- PollCat III 1
- Table of Contents 3
- List of Figures 6
- List of Tables 6
- 1. Introduction 7
- Disclaimer on Toll Fraud 8
- Typographic Conventions 8
- 2. Unit Description 9
- 2.2. Back Panel 10
- 3. Hardware Installation 11
- 3.1.5. Power Up Default (Sw8) 13
- 3.2.1. PBX Inputs A and B 14
- 3.2.2. Modem Port 15
- 3.2.3. Computer Port 15
- 4. Program Set-Up 16
- 4.1.2. Set General Parameters 17
- 4.3.2. The CRC Function 25
- 4.3.3. The Line I.D. Function 25
- RESTARTS,REXMITS,TIMEOUT 28
- 4.4.2. Scheduled Callback 29
- 4.4.3. 80% Full Callback 30
- 4.4.4. Immediate Callback 30
- Mode Command String 31
- 4.6. The Data Filter 33
- 5. The No-Data Alarm 34
- 6. The Data Filter 37
- 6.3. Enabling the Data Filter 40
- 6.5.1. AND Conditions 42
- 6.5.2. OR Conditions 43
- Conditions 47
- 7.2. Alarm Clues 52
- 7.2.1. Alarm Clue Definition 53
- 7.2.4. Real-Time Variables 56
- 7.2.5. Testing Alarm Clues 58
- 7.3.1. Alarm Off (^B87,0) 59
- 7.3.2. Local Alarm (^B87,1) 60
- 7.3.3. Remote Alarm (^B87,2) 60
- 7.3.4. Pager (Alpha) (^B87,3) 61
- 7.3.5. Report (^B87,4) 62
- 7.3.8. The Alarm Message 64
- Status (^B83) 66
- 8.1. ^B99 Command Options 70
- Parameters 72
- 9. Polling Accumulated Data 73
- 9.2. Polling 75
- Via Computer Port 78
- 10. Command Reference Guide 81
- ^ B00 Move Memory Partition 82
- ^ B01 Data Release Mode 83
- ^B12 Define Callback Schedule 86
- ^B13 Send ID / Alarm Message 86
- BATTERY GOOD ACK 91
- BATTERY LOW NAK 91
- ^B28 Enter Echo Test Mode 92
- ^B29 Enter Pass-Through Mode 93
- ^ B30 Exit to Command Mode 93
- ^ B37 Load and Test Memory 93
- ^ B53 Select Compression Mode 96
- ^ B62 Select Output Format 99
- ^B70 Select Callback Options 102
- ^B80 Define Block Size 104
- ^B81 Define Alarm Clue 105
- ^B82 Delete Alarm Clue(s) 105
- ^B84 Clear Alarm Condition 106
- Alarm Clue Counters 106
- ^B89 Test Pager 107
- ^B94 Enter Monitor Mode 110
- ^B95 Display EPROM Version 111
- ^B99 Save Parameter Settings 111
- A.2. Alarm Clue Definition 116
- A.3. Clue Definition Logic 124
- A.4. Programming Support 126
- B. Cable Installation 127
- C.3. Alarm Port 130
- D. PollCat II Compatibility 131
- D.3. Status Screens 132
- D.4. Connection 133
- E. LED Indicators 134
- F. Specifications 135
- G. Customer Service 136
- H. FCC Statement 137
- I.1. Response Message Summary 143
Verwandte Produkte und Handbücher für Telefone Western Telematic PollCat III
(174 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.245 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern