Western-telematic AT COMMAND SET MT9234 Bedienungsanleitung

WTI Part No. 13513 Rev. BMT5634/MT9234Internal ModemAT Command Set

3-2MT5634/MT9234 Modem; AT Command SetCommand: Ds DialValues: s = dial string (phone number and dial modifiers)Default: noneDescription: Dia

3-3AT CommandsCommand: Hn Hook ControlValues: n = 0 or 1Default: 0Description: H0 Go on-hook (hang up). H1 Go off-hook (make the phon

3-4MT5634/MT9234 Modem; AT Command SetCommand: P Pulse DialingValues: P, TDefault: TDescription: Configures the modem for pulse (non-touch-t

3-5AT CommandsCommand: Wn Result Code OptionsValues: n = 0, 1, or 2Default: 2Description: W0 CONNECT result code reports serial port spee

3-6MT5634/MT9234 Modem; AT Command SetCommand: &Dn Data Terminal Ready (DTR) ControlValues: n = 0, 1, 2, or 3Default: 2 Description: &a

3-7AT CommandsCommand: &Ln Leased Line OperationValues: n = 0, 1, or 2Defaults: 0Description: &L0 The modem is set for standard di

3-8MT5634/MT9234 Modem; AT Command SetCommand: &Tn Loopback Test (V.54 Test) CommandsValues: n = 0, 1, 3, 6Default: NoneDescription: Th

3-9AT CommandsCommand: \An Select Maximum MNP Block SizeValues: n = 0, 1, 2, or 3Default: 3Description: \A0 64-character maximum \A1 1

3-10MT5634/MT9234 Modem; AT Command SetCommand: \Nn Error Correction Mode SelectionValues: n = 0–5, or 7Default: 3Description: \N0 Non-err

3-11AT CommandsCommand: \Xn XON/XOFF Pass-ThroughValues: n = 0 or 1Default: 0Description: \X0 Modem responds to and discards XON/XOFF char

3-12MT5634/MT9234 Modem; AT Command SetCommand: %DCn AT Command ControlValues: n = 0 or 1Default: 0Description: %DC0 The modem responds t

3-13AT CommandsCommand: $EBn Asynchronous Word LengthValues: n = 0 or 1Default: 0Description: $EB0 Enables 10-bit mode. $EB1 Enables 1

3-14MT5634/MT9234 Modem; AT Command SetCommand: +VDR=x, y Distinctive Ring ReportValues: x = 0, 1 Distinctive Ring report control. Se

3-15AT CommandsCommand: #CBF? Callback Failed Attempts DisplayValues: N/ADefault: N/ADescription: Requests the number of failed callback pa

3-16MT5634/MT9234 Modem; AT Command SetCommand: #CBSn Callback Enable/DisableValues: n = 0, 1, 2, or 3Default: 0Description: #CBS0 Disable

4-14. S-RegistersCertain modem values, or parameters, are stored in memory locations called S-Registers. Use the S command to read or to alter the co

4-2MT5634/MT9234 Modem; AT Command SetRegister Unit Range Default DescriptionS37 decimal 0–19 0 Sets the maximum V.34 "upstream" spe

4-3S-RegistersRegister Unit Range Default DescriptionS48 decimal 7 or 128 7 Enables (7) or disables (128) LAPM negotiation. The follo

4-4MT5634/MT9234 Modem; AT Command Set

5-15. Result Codes In command mode your modem can send responses called Result Codes to your computer. Result codes are used by communications progra

iTable of Contents1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2MT5634/MT9234 Modem; AT Command SetTerse Verbose Description80 CONNECT 52000 Connected at 52000 bps81 CONNECT 54000 Connected at 54000 bps82

6-16. Remote Configuration and Country Code Configuration6.1. Remote ConfigurationRemote configuration is a network management tool that allows yo

6-2MT5634/MT9234 Modem; AT Command Set6.1.2.1. Changing the Setup Password1. Open a data communications program such as HyperTerminal.2. In the ter

6-3Remote Confi guration and Country Code Confi guration6.2. Country Code ConfigurationDifferent countries have different requirements for how modems m

6-4MT5634/MT9234 Modem; AT Command Set

5 Sterling • Irvine • California 92618 (949) 586-9950 • Toll Free: 1-800-854-7226 Fax: (949) 583-9514 • http://www.wti.com

iiMT5634/MT9234 Modem; AT Command Set

1-11. IntroductionThe AT commands are used to control the operation of your modem. They are called AT commands because the characters AT must precede

1-2MT5634/MT9234 Modem; AT Command SetYou can issue several commands in one line, in what is called a command string. The command string begins with A

2-12. AT Command Summary Organization of AT Commands on the following pages: 1st, by the initial command character (&, +, %), 2nd, alphabetized b

2-2MT5634/MT9234 Modem; AT Command SetCommand Description\Bn Transmit Break\Kn Break Control\Nn Error Correction Mode Selection\Qn Flow Control Select

3-13. AT Commands Command: AT Attention CodeValues: N/ADescription: The attention code precedes all command lines except A/, A: and escap